Save 
Your Basket- Your basket is currently empty
Log In
Call Us
Quick Links
- KIRBY Spares, Parts & Accessories
- HENRY Spares, Parts & Accessories
- MIELE Spares, Parts & Accessories
- SEBO Spares, Parts & Accessories
- KIRBY Legend II Spares & Accessories
- KIRBY G3 Spares, Parts & Accessories
- KIRBY G4 Spares, Parts & Accessories
- KIRBY G5 Spares, Parts & Accessories
- KIRBY G6 Spares, Parts & Accessories
- KIRBY Ultimate 'G' Spares, Parts & Accessories
- DYSON DC04 Spares, Parts & Accessories
- DYSON DC07 Spares, Parts & Accessories
- DYSON DC14 Spares, Parts & Accessories
- DYSON DC15 Spares, Parts & Accessories
- DYSON DC16 Spares, Parts & Accessories
- DYSON DC18 Spares, Parts & Accessories
- DYSON DC21 Spares, Parts & Accessories
Product Search
Top Searches
Price Match
Secure Site
Replacing the Pre Motor Filter
1. Start by pushing the locating ring above the filter housing forward to release the filter housing. 2. Remove the filter housing by sliding it out from the main body. 3. After removing the pre filter from its housing it can be cleaned by first pulling the inner section out of the outer cylinder. Then rinsing the inner section with ...
Replacing the Post Motor Filter
1. Start by pushing the locating ring above the filter housing forward to release the pre motor filter housing 2. Remove the pre motor filter housing by sliding it out from the main body. 3. Carefully release the thin plastic handle on top of the post motor HEPA filter. 4. Use the handle to pull the pos...
Replacing the Hose
1. Start by removing the power cable from the rear of the Dyson and then detach the wand handle from the main body and allow the hose to lie on the floor. Next, at the bottom of the hose, pull in the tab at the rear. 2. Allow the cassette assembly to fall away from the dyson and then press the brightly coloured tab to remove the hose itself. ...
Replacing the Wheels
1. Start by laying your Dyson onto it's side and, using a thin flat bladed screwdriver, prise off the glamour cap (hub cap) from the wheel. 2. After removing the circlip holding the wheel onto the axle the wheel can be simply pulled off the axle. Reassembly is a simple matter of reversing the steps listed above.
Replacing the Brush Roll
1. Start by laying your Dyson onto it's back and, using a two pence piece, turn each of the three soleplate fasteners a quarter of a turn in an anti-clockwise direction. 2. Remove the soleplate by prising it, underneath the centre soleplate fastener, away from the cleaner head. 3. Grasp the brush Roll in the centre and c...
Replacing the Cable
1. Start by unwinding the cable and then remove the wand assembly from the rear of the Dyson. Then, using the specially bent small screwdriver. gently push the screwdriver into the gap between the switch cover and the main body. To gently push the locating lug on the switch cover out of its socket. Place a thin screwdriver into the gap that you have created and, using the same method, release the...
Replacing the Switch
1. Start by unwinding the cable and then remove the wand assembly from the rear of the Dyson. Then, using the specially bent small screwdriver. gently push the screwdriver into the gap between the switch cover and the main body. To gently push the locating lug on the switch cover out of its socket. Place a thin screwdriver into the gap that you have created and, using the same method, release the...
Replacing the Motor
1. Lay your Dyson onto it's back and, using a two pence piece, turn each of the three soleplate fasteners a quarter of a turn in an anti-clockwise direction. 2. Remove the soleplate by twisting either side of the centre plastic screw. 3. Grasp the brush Roll in the centre and carefully pull it away from the cleaner head. ...