Product Search

 

Top Searches

 

Price Match

Price Match
 

Secure Site

Secure Site
 

Quick Links

 
You are here:  » Help and Support » Dyson Section » Dyson Technical Advice » DYSON DC04 Technical Advice
image:Replacing the Pre Motor Filter

Replacing the Pre Motor Filter

PLEASE NOTE: Always disconnect the Dyson from the mains before commencing work.1. Start by removing the cyclone/bin assembly from the main body.   2. Gain access to the pre motor filter by depressing the catch on the top of the cyclone.   3. Remove the pre motor filter and seperate the blue sponge section from th...

Read full article...

image:Replacing the Post Motor Filter

Replacing the Post Motor Filter

PLEASE NOTE: Always disconnect the Dyson from the mains before commencing work.1. Start by removing the cyclone/bin assembly from the main body.   2. Remove the post motor filter by twisting a two pence piece between the two semi-circular tabs at the rear of the post motor filter lid.   3. Beneath the lid you will ...

Read full article...

image:Replacing the Belt (Models WITHOUT Brush Control)

Replacing the Belt (Models WITHOUT Brush Control)

PLEASE NOTE: Always disconnect the Dyson from the mains before commencing work. Although the Dyson featured in the pictures is a DC07 Standard, the steps for changing the belt are identical to DC04 models. 1. Start by laying your Dyson onto it\'s back and using a two pence piece, turn each of the three soleplate fasteners a quarter of a turn in an anti-clockwise direction. ...

Read full article...

image:Replacing the Hose

Replacing the Hose

PLEASE NOTE: Always disconnect the Dyson from the mains before commencing work. 1. Firstly remove the power cable from the rear of your DC04 then release the wand handle from the main body. Then, press the uppermost brightly coloured button on the hose cuff to release the wand from the hose.    2. Then, at the rear of your Dyson, press in the brightly coloure...

Read full article...

image:Replacing the Wheels

Replacing the Wheels

PLEASE NOTE: Always remove the plug from the socket before commencing work. 1. Start by laying your Dyson on to it's side and, using a thin flat bladed screwdriver prise off the glamour cap (Hub cap) from the wheel.   2. After removing the circlip holding the wheel onto the axle. The wheel can be simply pulled off the axle.   ...

Read full article...

image:Replacing the Brush Roll (Models WITH Brush Control)

Replacing the Brush Roll (Models WITH Brush Control)

PLEASE NOTE: Always remove the plug from the socket before commencing work. 1. Start by laying your Dyson onto it's back and, using a two pence piece, turn each of the three soleplate fasteners a quarter of a turn in an anti-clockwise direction.   2. Remove the soleplate by prising it away from the cleaner head, underneath the c...

Read full article...

image:Replacing the Brush Roll (Models WITHOUT Brush Control)

Replacing the Brush Roll (Models WITHOUT Brush Control)

PLEASE NOTE: The actual Dyson featured in the pictures is a DC07 model without Brush Control. The steps taken to the remove the Brush Bar is identical to DC04 models. PLEASE NOTE: Always disconnect the Dyson from the mains before commencing work. 1. Start by laying your Dyson onto it's back and, using a two pence piece, turn each of the three soleplat...

Read full article...

image:Replacing the Switch

Replacing the Switch

PLEASE NOTE: If your are in anyway unsure of any of the steps listed below. Please consult a qualified electrician and always remove the plug from the socket before commencing work. 1. Start by unwinding the cable from the back of the Dyson. Then, depress the switch cover (glamour cap) to reveal a small notch behind the switch cover.   2...

Read full article...

image:Replacing the Cable

Replacing the Cable

PLEASE NOTE: If your are in anyway unsure of any of the steps listed below. Please consult a qualified electrician and always remove the plug from the socket before commencing work.    1. Start by unwinding the cable from the back of the Dyson. Then, depress the switch cover (glamour cap) to reveal a small notch behind the switch cover. ...

Read full article...

image:Replacing the Clutch

Replacing the Clutch

PLEASE NOTE: .If your are in anyway unsure of any of the steps listed below. Please consult a qualified electrician and always disconnect the Dyson from the mains before commencing work. 1. Start by removing the cyclone/bin assembly from the main body.   2. lay your Dyson onto it's back and, using a two pence piece, turn each of...

Read full article...

image:Replacing the Motor (Models with Brush Control)

Replacing the Motor (Models with Brush Control)

PLEASE NOTE: If your are in anyway unsure of any of the steps listed below. Please consult a qualified electrician and always disconnect the Dyson from the mains before commencing work. 1. Start by removing the cyclone/bin assembly from the main body.   2. Remove the post motor filter cover by using a two pence piece to twist the c...

Read full article...